PC/104 Ethernet Ethernet Card The PC/104 Ethernet Ethernet Card is an efficient solution that provides system designers the flexibility to include Ethernet Ethernet functionality into any PC/104 based system, with minimal engineering resources. The 16-bit Ethernet Ethernet card features -40oC to +85oC extended operating temperature. It is fully IEEE802.3 compatible. The card delivers full duplex Ethernet data transmission at speed up to 10Mbps. Installation is easy, the PC/104 Ethernet Ethernet card has built in RJ-45 connector, 10Base-T transceiver and optional BNC connector support 10Base-2. It can be installed under PnP and Jumper-less methods or using Jumper selection. The card is fully NE2000 compatible. It supports network operating systems (NOS) including OS/2 LAN, Novell NetWare and Microsoft Ethernet Manager.
Features: Full IEEE 802.3 compliant High Speed 10Mbps data transfer rate (up to 20Mbps in full duplex mode) Standard 10BASE-T RJ-45 port Optional 10BASE-2 coaxial connector Optional AUI port support for external transceiver Software compatible with Novell® NE-2000 Support for 8-bit or 16-bit bus Jumperless mode and PnP mode capable Configurable with on-board EEPROM for jumperless mode Interface auto-detect Auto polarity correction for 10BASE-T Full duplex capable Build in 16K SRAM Improved performance with data prefetch function 3 levels of power down sleep modes Support 8 IRQs, 16 I/O base addresses RIPL boot PROM for remote boot and diskless operation (sold separately) 5 V operation 3.775" x 3.550" x 0.435" (with low profile RJ-45 jack) On board LED's for Ethernet and link activity Software drivers included*
Ordering Information: Models Built-in Connectors PC104-ELC 10Base-T (RJ-45) PC104-ELC-2 10Base-2 (BNC Coaxial), 10Base-T (RJ-45) and AUI External Transceiver Connectors *Drivers Supported: NetWare ODI DOS Client NetWare ODI OS/2 Client NetWare ODI Server OS/2 NDIS2 for Microsoft Ethernet Manager DOS NDIS2 for Microsoft Ethernet Manager Windows NT/95/2000 NDIS3 WFW NDIS3 Windows CE 3.0 Linux 2.0 kernel Linux 2.1 and above kernel SCO UNIX PSOS UNIX Ratings @ 25o C Parameter Min Max Units Operating Temperature -40 +85 oC Relative Humidity (non-condensing) 0 +90 o/o Voltage Requirement 4.75 5.25 V Power Consumption 550 750 mW Specifications Standard IEEE 802.3 Topology Bus or Star Protocol CSMA/CD Dip switch PROM type select UTP/STP cabling CAT 3 or 5 LED Indicators Link, Tx / Rx, collision Support Settings IRQ 2/9, 3, 4, 5, 10, 11, 12, 15 I/O Base Address 200, 220, 240, 260, 280, 2A0, 2E0, 300, 320, 340, 350, 360, 380, 3A0, 3C0, 3E0 Boot PROM Base Memory C000, C400, C800, CC00, D000, D400, D800, DC00 Boot PROM type 256K, 512K, 1M Flash Click here for Mechanical Diagram & Pin Assignments Diagram Information furnished by Radicom Research is believed to be accurate and reliable.  However Radicom Research assumes no responsibility for its use, or any infringement of patents or other rights of third parties which may result from its use.  Radicom Research reserves the right to change circuitry at any time without notice.  This document is subject to change without notice. The information contained herein is subject to change without notice. Logos, trademarks and copyrights are property of their respective owners.

[ Home ][ Company ][ Products ][ Contact Us ][ Career ][ Patents ]